Skip to main content

[OVERCLOCK] AMD A8-5600K @4.3GHz STOCK COOLER

AMD A8-5600K ini merupakan seri APU dari AMD yang menggabungkan GPU dan CPU Quad-Core menjadi 1 chip processor. Didesain untuk level menengah kebawah, sangat cocok untuk user yang menginginkan komputer gaming dengan harga terjangkau dan spesifikasi lumayan. A8-5600K terintegrasi dengan GPU HD7560D. 

A8-5600K mempunyai clock speed sebesar 3.6GHz dengan tambahan turbo clock speed mencapai 3.9GHz. Seperti yang sudah saya baca disini, A8-5600K ini mampu berjalan pada clock speed @4.3GHz dengan stock cooler (pendingin bawaan). Saya dibantu Tiky kemudian mencobanya dengan menggunakan software bawaan motherboard, kebetulan motherboard saya ASRock dibekali dengan ASRock Extreme Tuning Utility dan software bawaan AMD yaitu AMD Overdrive.

Langkah pertama, matika AMD Turbo Core pada UEFI, set ke Disabled, hal ini untuk mengantisipasi supaya clock speed tidak berubah ke default lagi.

AMD A8-5600K @4.1GHz
Percobaan dengan meningkatkan voltage yang semula 1.375v menjadi 1.425v dengan menggunakan AMD Overclock. Pada mulanya multiplier sebesar 36x diganti menjadi sebesar 41x, hal ini tidak bisa dilakukan sebelum anda mengganti voltagenya menjadi 1.425v. AMD Overdrive akan mematikan Turbo Core untuk bisa mengubah multipliernya, tekan OK jika ditanya demikian.


Pengukuran suhu menggunakan ASRock Extreme Tuning Utility yang menurut saya PALING BENAR dibanding software pengukur suhu lainya. Software pengukur suhu lainya yang meurut saya KELIRU adalah CoreTemp, AIDA64 Extreme Edition, HWiNFO, dan HWMonitor. Belum tahu pasti apakah kekeliruan pada driver sensor yang ada pada processor, saya percayakan pengukuran suhu processor terhadap ASRock Extreme Tuning Utility. Pada saat idle, suhu CPU berada pada 39 derajat dan suhu motherboard berada pada 38 derajat.



AMD A8-5600K @4.3GHz 
Percobaan selanjutnya adalah menggunakan A8-5600K mencapai 4.3GHz. Caranya adalah dengan meningkatkan voltage menjadi 1.45volt dan menaikan multiplier menjadi 43x. 


Pada clock speed @4.3GHz menunjukan kenaikan suhu menjadi 40-45 derajat pada saat penggunaan idle dan AMD A8-5600K stabil pada @4.3GHz. Namun pada penggunaan sehari - hari, saya menggunakan clock speed @4.1GHz.






Clock speed ini biasanya naik turun tergantung penggunaan task yang aktif pada komputer anda, jika anda ingin mengunci pada kecepatan 4.1 atau 4.3, pada AMD Overdrive ada tombol seperti lampu hijau pada pojok kanan atas, tekan tombol tersebut maka clock speed akan stabil pada kecepatan yang anda tentukan. INGAT ! Clock speed yang stabil pada kecepatan tinggi akan memakai konsumsi daya yang lebih banyak.


GOOD LUCK, SELAMAT MENCOBA !

Comments

Popular posts from this blog

HackRF Mayhem Failed to Update - M0 Guru Meditation Hard

I was on Mayhem Portapack v2.0.1 and want to upgrade to the latest stable release v2.1.0. The update went okay using the web upgrade https://hackrf.app/. But then I saw the latest nightly update and want to try it, since it has many new tools that are not yet included in the stable release. But then the update failed :( Disclaimer: I didn't take any photos of the errors, since I was focused on googling the solution. So the error was " Bad Firmware or Failed W/R error" during the upgrade process, and it was stuck. So I had to restart the device, and it was booting to the Mayhem menu, but on the bottom left, which should show the current firmware version, it was showing a  "FLASH ERR"  message. I think I should go back to the stable release, but I can't. Every time I want to flash the stable release version, the portapack will shows an error M0 Guru Meditation - Hard Fault.  There's an issue that was closed on the Mayhem GIT repo that has the same issue a...

Fiberhome HG6145D2 Superadmin Login

Maybe some of you are using In**ehome ISP as your home internet and found out that using the provided login has minimal options to configure the router: user  user1234 I know it’s not the admin login, and that must be a full-control user account that can be used to control this router fully. So I searched and found some posts on the net and most of them are telling me to use: admin %0|F?H@f!berhO3e I tested it and it doesn’t work! But there’s more to it, you need to reset the router first by pressing the reset button on the side of the router. Then after resetting, you can log in using the admin superaccount! But keep in mind, never use the user log in again, because it will lock the super admin login until you reset the router again. Cheers 🍺

Macintosh Classic II Brightness Issue

The Problem My Macintosh Classic II suffers from an issue where the display CRT goes dim after a few minutes on a cold boot. Every time it happens, I need to crank up the cut-off and brightness  pot behind the machine to show the image. The Analyze At first, I thought it must be the brightness issue, so I searched for the Macintosh Classic analog board schematic to check the brightness line. I found the schematic from Bomarc, and the schematic is suitable with my board, since there are two analog board versions.  I started to suspect the resistors and potentiometer on the brightness line. This Macintosh version has software-controlled brightness, so the analog board will get a 22.25 kHz square wave PBM signal from the logic board to control the brightness. I checked and replaced some resistors and cleaned the potentiometer, but nothing seems to work. The signal is there, and no sign of degradation that makes the screen dim after a few minutes.  Brightness Line So I suspec...