Skip to main content

[MOTO G] Baterai habis, dicharge tidak menyala

Moto G buatan Motorola ini memang memiliki baterai dengan kapasitas 2000 mAh dengan desain tidak bisa dicopot yang cukup membingungkan ketika ada masalah seperti ini. Sesuai dengan judul, hari ini saya mengalami masalah tersebut, dimana baterai Moto G saya habis (benar-benar kosong) sampai saat saya coba menyalakan lagi, lampu LED nya tidak berkedip-kedip  karena mungkin sudah tidak kuat untuk menyalakanya lagi.

Moto G Baterai (non removable)

Sesaat saya lakukan charging menggunakan PC, smartphone ini menyala menunjukan gambar baterai yang kemudian mati layarnya, saya anggap normal - normal saja, sampai 15 menit kemudian saya cek lagi, ternyata tidak dapat menyala, dan proses charging pun tidak terjadi.

Setelah saya cari - cari di berbagai forum Moto G, ternyata banyak yang mengalami masalah yang sama, berikut cara - cara yang disarankan

  1. Charge 24 jam penuh, tanpa diganggu gugat !
  2. Sambungkan charger, tekan tombol power selama 1 menit sampai layar menyala logo Motorola
  3. Sambungkan charger, tekan tombol power selama 2 menit sampai lampu LED charging menyala
  4. Gunakan charger asli bawaan Motorola. (Beberapa seri Amerika mungkin tidak dibawakan)
Dari 4 cara tersebut, cara yang work adalah nomor 3 pada kasus saya. Selama 2 menit kurang beberapa detik (ya, saya menggunakan timer), lampu LED charging langsung menyala dan saya lega :D

Selamat mencoba

Comments

Post a Comment

Popular posts from this blog

HackRF Mayhem Failed to Update - M0 Guru Meditation Hard

I was on Mayhem Portapack v2.0.1 and want to upgrade to the latest stable release v2.1.0. The update went okay using the web upgrade https://hackrf.app/. But then I saw the latest nightly update and want to try it, since it has many new tools that are not yet included in the stable release. But then the update failed :( Disclaimer: I didn't take any photos of the errors, since I was focused on googling the solution. So the error was " Bad Firmware or Failed W/R error" during the upgrade process, and it was stuck. So I had to restart the device, and it was booting to the Mayhem menu, but on the bottom left, which should show the current firmware version, it was showing a  "FLASH ERR"  message. I think I should go back to the stable release, but I can't. Every time I want to flash the stable release version, the portapack will shows an error M0 Guru Meditation - Hard Fault.  There's an issue that was closed on the Mayhem GIT repo that has the same issue a...

Fiberhome HG6145D2 Superadmin Login

Maybe some of you are using In**ehome ISP as your home internet and found out that using the provided login has minimal options to configure the router: user  user1234 I know it’s not the admin login, and that must be a full-control user account that can be used to control this router fully. So I searched and found some posts on the net and most of them are telling me to use: admin %0|F?H@f!berhO3e I tested it and it doesn’t work! But there’s more to it, you need to reset the router first by pressing the reset button on the side of the router. Then after resetting, you can log in using the admin superaccount! But keep in mind, never use the user log in again, because it will lock the super admin login until you reset the router again. Cheers 🍺

Macintosh Classic II Brightness Issue

The Problem My Macintosh Classic II suffers from an issue where the display CRT goes dim after a few minutes on a cold boot. Every time it happens, I need to crank up the cut-off and brightness  pot behind the machine to show the image. The Analyze At first, I thought it must be the brightness issue, so I searched for the Macintosh Classic analog board schematic to check the brightness line. I found the schematic from Bomarc, and the schematic is suitable with my board, since there are two analog board versions.  I started to suspect the resistors and potentiometer on the brightness line. This Macintosh version has software-controlled brightness, so the analog board will get a 22.25 kHz square wave PBM signal from the logic board to control the brightness. I checked and replaced some resistors and cleaned the potentiometer, but nothing seems to work. The signal is there, and no sign of degradation that makes the screen dim after a few minutes.  Brightness Line So I suspec...