Skip to main content

[Teardown] Ocean Radio WR-232

Radio sekarang mulai beralih dari analog radio menuju ke internet radio yang bersifat streaming. Belum terlalu booming di Indonesia karena memang akses internet masih tergolong mahal dan terbatas. Kebetulan saya menemukan sebuah Desktop Internet Radio dengan merk Ocean Digital WR-232. Anda bisa melihat infonya di situs officialnya http://www.oceandigitalshop.com/

Sedikit sekali info yang bisa saya dapatkan di internet tentang produk ini. Produk ini diproduksi di China dan kebanyakan infonya berbahasa china yang saya tidak mengerti. Kualitas dari produk ini tidak mengecewakan, bodi terbuat dari kayu dan plastik.

Ocean Radio WR-232
Oke langsung saja, siapkan peralatan untuk teardown !
Langkah pertama adalah membuka 6 sekrup yang ada dibelakang radio. Bagian belakang yang dilepas terdapat board yang mengurusi tentang amplifier dan untuk regulator tegangan. 


Walaupun agak tidak terlihat jelas, untuk chip regulator radio ini menggunakan TD1482 yang merupakan chip step-down untuk menurunkan tegangan. Sedangkan untuk amplifiernya menggunakan UTC7266 yang merupakan dual bridge amplifier. Chip ini yang mengendalikan suara output yang saya anggap sudah cukup enak didengar.

Chip regulator TD1482 (pojok kiri)

Chip UTC7266 (kanan)
Langkah selanjutnya adalah mencopoti bagian depan radio yang bisa dengan mudah dengan mencopot sekrup yang menempel pada dinding body radio. Nilai positif dari radio ini adalah boardnya bersifat modular dan mudah dilepas menjadi perbagian. Bagian depan radio ono hanya terdapat LCD, sebuah rotary encoder, sebuah infrared sensor dan 3 buah push button.

Tampak depan radio
Tampak belakang boardnya terdapat beberapa chip, diantaranya adalah chip dengan nomor seri Holtek HT46R23 yang merupakan sebuah 8-bit OTP microcontroller. Dilihat sekilas dari jalur PCBnya, chip ini digunakan untuk mengatur papan kontrol tombol yang berada disisi atas radio.

Holtek HT46R23

Chip berikutnya adalah NAU8822A yang merupakan produksi Nuvoton dan berfungsi sebagai 24bit Stereo Audio Codec yang sudah dilengkapi dengan Speaker driver. Chip ini juga yang menghandle fitur Equalizer yang terdapat pada WR232 dimana mempunyai 5 band equalizer.

Nuvoton NAU8822A
Chip selanjutnya berada disebuah modul WiFi besutan Atheros dengan chip yang bertuliskan Atheros AR9331 yang sudah terbundling dengan sebuah modul besutan Skylab dengan seri M803. Modul ini dapat dibeli disini.


Dari sisi software, setelah saya scan menggunakan nmap, terdapat 4 port tcp dan 2 port udp yang terbuka yaitu port 23, 80, 5002, 49152. Port 5002 merupaka port RFE, dan port 49152 merupakan port UPNP, Saya tertarik untuk menembus port 23 yang merupakan port telnet, namun belum tahu username passwordnya, mungkin nanti akan saya coba - coba kembali. Sedangkan port UDP yang terbuka adalah port 1900 untuk UPNP dan port 5353 untuk zeroconf.

Overall radio ini memuaskan, dari sisi fitur dan output suara juga bagus. Bisa anda pertimbangkan jika anda mencari sebuah desktop internet radio dengan harga yang miring. 


Comments

  1. masbro, kalo ocean digitalnya mau dijual kabari ya.. mau beli baru susah banget yg ready stock

    ReplyDelete
    Replies
    1. Hehe.. sementara ini belum, masih buat alarm kalau pagi.
      Di tokopedia / bukalapak habis semua po?

      Delete
  2. semua seller habis stok.. kalo kang felix ada source aku mohon dibisiki ya.. suwun

    ReplyDelete
    Replies
    1. walah. aku dulu kalau ga salah juga di tokped pakai cicilan 12 bulan, sampai sekarang malah belum lunas.. hehehe
      Ok coba besok kalau ada info saya kabari

      Delete
    2. siapp! suwun bgt kang.. ditunggu kabarnya

      Delete

Post a Comment

Popular posts from this blog

HackRF Mayhem Failed to Update - M0 Guru Meditation Hard

I was on Mayhem Portapack v2.0.1 and want to upgrade to the latest stable release v2.1.0. The update went okay using the web upgrade https://hackrf.app/. But then I saw the latest nightly update and want to try it, since it has many new tools that are not yet included in the stable release. But then the update failed :( Disclaimer: I didn't take any photos of the errors, since I was focused on googling the solution. So the error was " Bad Firmware or Failed W/R error" during the upgrade process, and it was stuck. So I had to restart the device, and it was booting to the Mayhem menu, but on the bottom left, which should show the current firmware version, it was showing a  "FLASH ERR"  message. I think I should go back to the stable release, but I can't. Every time I want to flash the stable release version, the portapack will shows an error M0 Guru Meditation - Hard Fault.  There's an issue that was closed on the Mayhem GIT repo that has the same issue a...

Fiberhome HG6145D2 Superadmin Login

Maybe some of you are using In**ehome ISP as your home internet and found out that using the provided login has minimal options to configure the router: user  user1234 I know it’s not the admin login, and that must be a full-control user account that can be used to control this router fully. So I searched and found some posts on the net and most of them are telling me to use: admin %0|F?H@f!berhO3e I tested it and it doesn’t work! But there’s more to it, you need to reset the router first by pressing the reset button on the side of the router. Then after resetting, you can log in using the admin superaccount! But keep in mind, never use the user log in again, because it will lock the super admin login until you reset the router again. Cheers 🍺

Macintosh Classic II Brightness Issue

The Problem My Macintosh Classic II suffers from an issue where the display CRT goes dim after a few minutes on a cold boot. Every time it happens, I need to crank up the cut-off and brightness  pot behind the machine to show the image. The Analyze At first, I thought it must be the brightness issue, so I searched for the Macintosh Classic analog board schematic to check the brightness line. I found the schematic from Bomarc, and the schematic is suitable with my board, since there are two analog board versions.  I started to suspect the resistors and potentiometer on the brightness line. This Macintosh version has software-controlled brightness, so the analog board will get a 22.25 kHz square wave PBM signal from the logic board to control the brightness. I checked and replaced some resistors and cleaned the potentiometer, but nothing seems to work. The signal is there, and no sign of degradation that makes the screen dim after a few minutes.  Brightness Line So I suspec...