Skip to main content

Fixing Sony ICF SW-77


Sudah lama ngga update blog lagi. Kali ini sekedar membagi tulisan tentang Sony ICF SW-77 yang saya dapat dari teman saya. Radio legend ini emang agak rare di Indonesia, jarang banget muncul di pasaran. Masalah yang sering di alami oleh radio seperti ini adalah kapasitor yang mulai pada bocor, terutama karena bentuknya SMD dan bocoranya mengenai komponen - komponen di sekitarnya ataupun sampai ke balik board lewat via pada PCB.

Kondisi radio ini ketika datang, layar kotor dan modul komputernya nyala namun modul RF nya tidak, sehingga cuma ngeses doang. Setelah saya bongkar ternyata beberapa komponen kapasitor sudah diganti semua. Namun ada beberapa kapasiotr yang pada waktu penggantianya kurang hati - hati sehingga membuat trace pada PCB menjadi terangkat dan putus. Korosi yang ditimbulkan oleh bocoran kapasitor sangat ganas, jadi hati - hati ketika mau mengganti kapasitor yang sudah bocor, jangan sampai trace sampai putus.

Setelah beberapa saat menelusuri bagian - bagian yang sekiranya fatal, saya curiga kenapa suara yang dihasilkan radio ketika mode FM dan AM suara desisnya sama. Harusnya AM suaranya lebih kotor dibandingkan dengan FM. Saya coba membetulkan dan membersihkan bagian kabel konektor dari modul komputer ke modul RF namun hasilnya sama saja. Kabel konektor juga masih dalam kondisi bagus.

Lalu saya trace lagi apakah ada tegangan ketika melakukan switch dari FM ke AM di bagian IC Band Select. Ternyata modul IC tersebut tidak bekerja sebagaimana mestinya seperti voltage yang terdapat di schematic. Setelah saya lihat posisinya di PCB, ternyata posisi IC tersebut berada berdekatan dengan kapasitor amplifier 470uf yang ukuranya besar dan bocoranya mengenai kaki - kaki IC tersebut.
IC Band Select Sony ICF-SW77
Langkah selanjutnya adalah mencopot chip yang bermasalah tersebut dan membersihkanya dengan alcohol. Selain chip tersebut, saya juga mencopot semua chip yang berdekatan dengan posisi kapasitor. Beberapa chip tersebut ternyata juga menjadi korban banjir bocoran kapasitor. Sekalian membersihkan lainnya akhirnya waktunya mencoba.
Kaki chip yang terkena bocoran kapasitor

Setelah proses penggantian kapasitor dan pembersihan PCB, akhirnya radio ini kembali berfungsi FM dan AM nya. Tidak ada komponen lain yang perlu diganti kecuali kapasitor - kapasitor tersebut. Beberapa saya ganti menggunakan kapasitor tantalum yang umurnya bisa lebih panjang.



Akhirnya 2 radio ini menyala semua, tapi radio yang satunya AM nya masih bermasalah, cuma bisa FM. Yang mau beli yang satunya, bisa kontak saya aja :)


Comments

Popular posts from this blog

HackRF Mayhem Failed to Update - M0 Guru Meditation Hard

I was on Mayhem Portapack v2.0.1 and want to upgrade to the latest stable release v2.1.0. The update went okay using the web upgrade https://hackrf.app/. But then I saw the latest nightly update and want to try it, since it has many new tools that are not yet included in the stable release. But then the update failed :( Disclaimer: I didn't take any photos of the errors, since I was focused on googling the solution. So the error was " Bad Firmware or Failed W/R error" during the upgrade process, and it was stuck. So I had to restart the device, and it was booting to the Mayhem menu, but on the bottom left, which should show the current firmware version, it was showing a  "FLASH ERR"  message. I think I should go back to the stable release, but I can't. Every time I want to flash the stable release version, the portapack will shows an error M0 Guru Meditation - Hard Fault.  There's an issue that was closed on the Mayhem GIT repo that has the same issue a...

Macintosh Classic II Brightness Issue

The Problem My Macintosh Classic II suffers from an issue where the display CRT goes dim after a few minutes on a cold boot. Every time it happens, I need to crank up the cut-off and brightness  pot behind the machine to show the image. The Analyze At first, I thought it must be the brightness issue, so I searched for the Macintosh Classic analog board schematic to check the brightness line. I found the schematic from Bomarc, and the schematic is suitable with my board, since there are two analog board versions.  I started to suspect the resistors and potentiometer on the brightness line. This Macintosh version has software-controlled brightness, so the analog board will get a 22.25 kHz square wave PBM signal from the logic board to control the brightness. I checked and replaced some resistors and cleaned the potentiometer, but nothing seems to work. The signal is there, and no sign of degradation that makes the screen dim after a few minutes.  Brightness Line So I suspec...

Fiberhome HG6145D2 Superadmin Login

Maybe some of you are using In**ehome ISP as your home internet and found out that using the provided login has minimal options to configure the router: user  user1234 I know it’s not the admin login, and that must be a full-control user account that can be used to control this router fully. So I searched and found some posts on the net and most of them are telling me to use: admin %0|F?H@f!berhO3e I tested it and it doesn’t work! But there’s more to it, you need to reset the router first by pressing the reset button on the side of the router. Then after resetting, you can log in using the admin superaccount! But keep in mind, never use the user log in again, because it will lock the super admin login until you reset the router again. Cheers 🍺