Skip to main content

Gagal Pairing Mifa dan Linux

Mifa M1 merupakan speaker bluetooth yang saya biasa gunakan sebagai speaker andalan ketika berpergian karena bentuknya mini dan daya tahan baterainya luar biasa, suaranya juga tidak kalah.
Baru kali ini saya mencoba pairing menggunakan komputer saya, biasa hanya pairing ke HP maupun tablet. Terdapat kendala ketika akan saya pairing ke komputer saya yang menggunakan Linux. Komputer saya tidak bisa melakukan pairing, selalu mental. Namun saya menemukan solusi untuk melakukanya hingga sukses. Ikuti perintah berikut ini jika anda menemui masalah yang sama. Saya sedang menggunakan kernel 4.10.0-37

$ bluetoothctl
[bluetooth]# power on
[bluetooth]# agent on
[bluetooth]# default-agent
[bluetooth]# scan on
[NEW] Device XX:XX:XX:XX:XX:XX Mifa M1
[bluetooth]# scan off
[bluetooth]# trust XX:XX:XX:XX:XX:XX
[bluetooth]# pair XX:XX:XX:XX:XX:XX
Attempting to pair with XX:XX:XX:XX:XX:XX
[CHG] Device XX:XX:XX:XX:XX:XX Connected: yes
[CHG] Device XX:XX:XX:XX:XX:XX UUIDs: ...
[CHG] Device XX:XX:XX:XX:XX:XX UUIDs: ...
[CHG] Device XX:XX:XX:XX:XX:XX UUIDs: ...
[CHG] Device XX:XX:XX:XX:XX:XX UUIDs: ...
[CHG] Device XX:XX:XX:XX:XX:XX UUIDs: ...
[CHG] Device XX:XX:XX:XX:XX:XX UUIDs: ...
[CHG] Device XX:XX:XX:XX:XX:XX UUIDs: ...
[CHG] Device XX:XX:XX:XX:XX:XX UUIDs: ...
[CHG] Device XX:XX:XX:XX:XX:XX
Paired: yes Pairing successful
[CHG] Device XX:XX:XX:XX:XX:XX Connected: no
[bluetooth]# connect XX:XX:XX:XX:XX:XX
Attempting to connect to XX:XX:XX:XX:XX:XX
[CHG] Device XX:XX:XX:XX:XX:XX Connected: yes
Connection successful
[bluetooth]# quit
Sudah ? jika sudah anda tinggal mengganti output device untuk sound anda ke Mifa M1 di setting jika anda menggunakan desktop KDE. Desktop yang lain menyesuaikan :)


UPDATE 31 January 2018
Saya menemukan cara yang lebih mudah yaitu menggunakan Blueman. Tinggal download Blueman yang sudah ber GUI dan hubungkan dengan MiFa anda.
Labels:

Comments

Post a Comment

Popular posts from this blog

HackRF Mayhem Failed to Update - M0 Guru Meditation Hard

I was on Mayhem Portapack v2.0.1 and want to upgrade to the latest stable release v2.1.0. The update went okay using the web upgrade https://hackrf.app/. But then I saw the latest nightly update and want to try it, since it has many new tools that are not yet included in the stable release. But then the update failed :( Disclaimer: I didn't take any photos of the errors, since I was focused on googling the solution. So the error was " Bad Firmware or Failed W/R error" during the upgrade process, and it was stuck. So I had to restart the device, and it was booting to the Mayhem menu, but on the bottom left, which should show the current firmware version, it was showing a  "FLASH ERR"  message. I think I should go back to the stable release, but I can't. Every time I want to flash the stable release version, the portapack will shows an error M0 Guru Meditation - Hard Fault.  There's an issue that was closed on the Mayhem GIT repo that has the same issue a...
Post a Comment
Read More...

Macintosh Classic II Brightness Issue

The Problem My Macintosh Classic II suffers from an issue where the display CRT goes dim after a few minutes on a cold boot. Every time it happens, I need to crank up the cut-off and brightness  pot behind the machine to show the image. The Analyze At first, I thought it must be the brightness issue, so I searched for the Macintosh Classic analog board schematic to check the brightness line. I found the schematic from Bomarc, and the schematic is suitable with my board, since there are two analog board versions.  I started to suspect the resistors and potentiometer on the brightness line. This Macintosh version has software-controlled brightness, so the analog board will get a 22.25 kHz square wave PBM signal from the logic board to control the brightness. I checked and replaced some resistors and cleaned the potentiometer, but nothing seems to work. The signal is there, and no sign of degradation that makes the screen dim after a few minutes.  Brightness Line So I suspec...
Post a Comment
Read More...

Fiberhome HG6145D2 Superadmin Login

Maybe some of you are using In**ehome ISP as your home internet and found out that using the provided login has minimal options to configure the router: user  user1234 I know it’s not the admin login, and that must be a full-control user account that can be used to control this router fully. So I searched and found some posts on the net and most of them are telling me to use: admin %0|F?H@f!berhO3e I tested it and it doesn’t work! But there’s more to it, you need to reset the router first by pressing the reset button on the side of the router. Then after resetting, you can log in using the admin superaccount! But keep in mind, never use the user log in again, because it will lock the super admin login until you reset the router again. Cheers 🍺
Post a Comment
Read More...